Operating tips for 54-in. (137-cm) mulching kit
Mulching:
Adjust baffle to the proper opening; the adjustable baffle can be moved to one of five positions to match conditions using the convenient wing nuts.
When mulching grass, the operator should start with the baffle set in the highest position (greatest opening).
In drier conditions or when mulching leaves, the baffle can be moved down to reduce the amount of material that is discharged.
The holes in the adjustable baffle are intended for leaf mulching. When mulching dry leaves, the holes will allow some air and leaf particles to escape, reducing blowout in other areas of the mower. However, when mulching grass, these holes can be expected to plug.
Mow when grass is dry.
Observe the one-third rule.
No more than one third of the grass blade should be cut off at one time. This allows more efficient mulching and will promote the continued good health of the grass. If the desired cut height cannot be achieved by cutting off one third, or there is clumping of the clippings, it may be required to cut higher. Wait a day, then lower the mower and make a second pass.
Mow at proper intervals - approximately every four to five days.
Always mow with sharp blades.
When using the mulch kit, clippings are held in suspension under the mower until the power take-off (PTO) is shut off or the engine speed is reduced to slow the mower blades. When ready to stop mulching, slowing the engine speed while continuing to drive over the cut area will allow the suspended clippings to fall and disperse more evenly over the lawn.
Tips for special situations:
If mulching performance is not satisfactory, raising the mower to increase cut height, even a little bit, will often make a big difference.
If excessive clippings appear at the left edge of the mower, the left rear mower lip should be removed (if the mower is so equipped). This will promote better distribution of clippings.
Side-discharging and using the Power Flow material collection system (MCS):
For side-discharging and using the 54C Power Flow MCS, remove the mulching attachment.
The special mulching blades may be used if satisfactory results are achieved. If not, remove and replace with standard blades.
Rubber front edges can be left on if side discharging, however, cut quality may be reduced slightly when mowing lush grass.
Bagging:
Remove mulching attachment and install the appropriate medium or high lift blade(s).
Installation and removal:The 54-in. (137-cm) Tricycler kit can be easily removed while the mower is mounted on the tractor.Only two cap screws and nuts, located at the front and right side of the mower, need to be removed.
D170
E180
G110
LA150
LA175
S180
Mulching:
Adjust baffle to the proper opening; the adjustable baffle can be moved to one of five positions to match conditions using the convenient wing nuts.
When mulching grass, the operator should start with the baffle set in the highest position (greatest opening).
In drier conditions or when mulching leaves, the baffle can be moved down to reduce the amount of material that is discharged.
The holes in the adjustable baffle are intended for leaf mulching. When mulching dry leaves, the holes will allow some air and leaf particles to escape, reducing blowout in other areas of the mower. However, when mulching grass, these holes can be expected to plug.
Mow when grass is dry.
Observe the one-third rule.
No more than one third of the grass blade should be cut off at one time. This allows more efficient mulching and will promote the continued good health of the grass. If the desired cut height cannot be achieved by cutting off one third, or there is clumping of the clippings, it may be required to cut higher. Wait a day, then lower the mower and make a second pass.
Mow at proper intervals - approximately every four to five days.
Always mow with sharp blades.
When using the mulch kit, clippings are held in suspension under the mower until the power take-off (PTO) is shut off or the engine speed is reduced to slow the mower blades. When ready to stop mulching, slowing the engine speed while continuing to drive over the cut area will allow the suspended clippings to fall and disperse more evenly over the lawn.
Tips for special situations:
If mulching performance is not satisfactory, raising the mower to increase cut height, even a little bit, will often make a big difference.
If excessive clippings appear at the left edge of the mower, the left rear mower lip should be removed (if the mower is so equipped). This will promote better distribution of clippings.
Side-discharging and using the Power Flow material collection system (MCS):
For side-discharging and using the 54C Power Flow MCS, remove the mulching attachment.
The special mulching blades may be used if satisfactory results are achieved. If not, remove and replace with standard blades.
Rubber front edges can be left on if side discharging, however, cut quality may be reduced slightly when mowing lush grass.
Bagging:
Remove mulching attachment and install the appropriate medium or high lift blade(s).
Installation and removal:The 54-in. (137-cm) Tricycler kit can be easily removed while the mower is mounted on the tractor.Only two cap screws and nuts, located at the front and right side of the mower, need to be removed.
Fits On
190CD170
E180
G110
LA150
LA175
S180
{"shipping_group":"Shipping Group|ESTIMATED_MEDIUM_SIZE","spec_notab_fits_on_multiselect":"Fits On|D170 with 54 Inch Deck","promoted_feature_entity_attribute":"Promoted Features|RDO Promise","sku":"SKU|BG20304","part_cdk_id":"Part ID|12943581","feature_bullet_1":"Feature 1|Superb Mulching Performance: The BG20304 54-in. mulch kit ensures exceptional mulching performance, transforming your mower into a high-efficiency mulching machine for a well-manicured lawn.","feature_bullet_2":"Feature 2|Effortless Conversion: Easily convert your mower into a mulching powerhouse with the BG20304 kit, providing a convenient and effective solution for grass recycling and lawn maintenance.","feature_bullet_3":"Feature 3|Optimized Grass Recycling: The mulching kit integrates seamlessly to optimize grass recycling, promoting a cleaner mowing experience and reducing the need for manual grass cleanup.","feature_bullet_4":"Feature 4|Uniform Cut and Finish: Experience a uniform cut and finish with the BG20304 mulch kit, ensuring a professional-looking lawn while promoting healthy grass growth and maintenance.","part_cdk_company":"Company|01","part_cdk_division":"Division|01","part_cdk_type_code":"Type Code|99","part_cdk_list_price":"List Price|379.86","part_cdk_part_class":"Part Class|TU2","part_cdk_branch_code":"Branch Code|99","part_cdk_branch_name":"Branch Name|Fargo FSO","part_cdk_description":"CDK Description|GRASS MULCHING","part_cdk_part_number":"Part Number|BG20304","part_cdk_part_source":"Part Source|GX","part_cdk_part_status":"Part Status|A","part_cdk_vendor_code":"Vendor Code|DEERE","part_cdk_vendor_name":"Vendor Name|JOHN DEERE","part_cdk_product_line":"Product Line|CPXXXX","feature_bullet_5":"Feature 5|Versatile Compatibility: This mulch kit is designed for versatile compatibility, catering to a wide range of mower models for comprehensive lawn care solutions.","spec_notab_51_weight":"Weight|26.6 Pound","spec_notab_512_middle_dimension":"Middle Package Dimension|11 Inch","spec_notab_511_largest_dimension":"Largest Package Dimension|37 Inch","spec_notab_513_smallest_dimension":"Smallest Package Dimension|7 Inch"}